Small sensors with an important job
The photo eyes near the bottom of your garage door send an invisible beam across the opening. An interrupted beam should prevent closing or reverse a closing door according to the opener’s design. They need a clear view of each other, and they are no substitute for keeping people and pets away from a moving door.
This guide expands Linde Overhead Door’s photo eye maintenance and safety flyer. Use your particular opener’s manual for cleaning, adjustment, indicator lights, and testing. If the door is crooked, damaged, or unstable, arrange service before operating it or attempting tests.
Clean gently and keep the beam clear
With the door stopped, gently wipe each lens with a soft, clean cloth. Follow the manufacturer’s cleaning instructions; avoid abrasive tools and do not spray cleaner into the sensor housing. Clear cobwebs, dust, leaves, and loose snow from around the sensors when it is safe to do so.
Keep bins, tools, shovels, and stored items out of the beam. In a New London garage, take another look after bringing in snowy equipment or moving winter storage. Clear the obstruction instead of raising the sensors above it.
Check alignment, brackets, and visible wiring
Both eyes should face each other at the same height. Look for a bumped or loose bracket, a cracked housing, or visibly pinched or damaged wire. Keep hands away from moving hardware. Leave damaged wiring and uncertain repairs to a technician.
Read the indicator lights using your model’s instructions. A color or flash pattern described for another brand may mean something different on yours. Lights that stay off, flicker, or repeatedly lose their normal indication deserve attention even if the door sometimes works.
For residential doors, DASMA’s TDS 364 says the beam must be no higher than 6 inches above the garage floor. Follow the opener manufacturer’s exact installation instructions; some specify a narrower height range. If placement is wrong or alignment needs adjustment, follow the manual or call for help. Disconnect power before sensor installation or adjustment as the manufacturer directs, then restore it only as instructed for testing.
Test the photo eyes every month
Start with the door fully open and follow your opener manual. Keep everyone away from the opening, stand safely outside the door’s travel path, and keep the door in sight. Use an object for each check, never a person or pet.
- Blocked-beam check: Place an object across the beam, then use the remote to request closing. The door should refuse to close as described in the manual. Some models may move a few inches and reverse; it must not continue closing through the blocked beam.
- Moving-door reversal check: Remove the object. Following the manual, start the door closing, then interrupt the beam with a long object from the side while your body stays clear of the opening. DASMA says the door should reverse and return fully open. If you cannot do this from a safe position, have a technician perform the test.
If either test fails, stop using the opener and call for service. Never bypass, disable, or reposition the photo eyes to defeat them. Holding a wall control to override a sensor problem is not a repair.
The contact-reversal test is separate
Also perform the separate monthly contact-reversal test in your opener manual. This checks the response when the door contacts the specified test object, rather than when the light beam is interrupted. Follow the manual’s object size, placement, and procedure. Passing a photo eye test does not replace this test.
If contact reversal fails, stop using the opener and arrange service. Do not increase force or adjust springs, cables, or bottom brackets to make a test pass. Those tension-system components belong in professional hands.
Get help with recurring sensor trouble
Note your opener model, what each sensor light does, and which test failed. For other symptoms, see our door-won’t-close guide. Linde Overhead Door serves Waupaca, Waushara, and Outagamie counties from New London. Call 920-538-6362 or 920-596-0004, 7 AM–7 PM, to discuss opener and safety-sensor service.
- DASMA TDS 364: photoelectric sensor placement and monthly testing
- DASMA: garage door opener safety and maintenance guide
- Chamberlain Group: safety-sensor alignment and height
- Chamberlain Group: testing the Protector System
- Genie: clean lenses, obstructions, wiring, and indicator lights
Follow the instructions for your particular door and opener. This guide does not replace an on-site assessment.
